Recent Posts

Pages: [1] 2 3 ... 10
1
General Discussion / Re: engine bay splash pans....
« Last post by kimmc on Today at 01:23:13 AM »
Hey Chet.  Thanks for taking the time to do this.  I think I can manage the fabrication from your very complete drawing.  Best, Kim Mc
2
General Discussion / Re: engine bay splash pans....
« Last post by chetbrz on January 15, 2018, 07:22:14 PM »
Kim & Tom,

I traced the front pan support.  The pictures below illustrate how I traced it.  The flat length of the material would be 17" long 16 gauge steel by 4.5"wide (actual measured 4 7/16" wide)

If you want I can make copies of the 8.5 x 14 document and send it to you.  Just email me your address.







If you can print an 8.5 X 14" document download the attached pdf file
3
General Discussion / Sill or Chassis rail dimensions 1929 Plymouth U
« Last post by Geoff57 on January 15, 2018, 05:42:59 AM »
I extrapolated the mirror image dimensions for the sills from four rotten sills which between them were 90% measurable
4
General Discussion / S11V Ignition points 1929 Plymouth U
« Last post by Geoff57 on January 15, 2018, 05:35:31 AM »
No ignition points were with the distrbutor (dizzy) when I picked up the Plymouth. The car was all pulled apart including the dizzy. The S11V points for some Australian Ford & GM cars late 60's to early 80's fit perfect. Just unclick the points arm contact from the housing
5
General Discussion / Re: Windshield wipper assy.
« Last post by 29UJohn on January 15, 2018, 02:45:28 AM »
There is an excellent article on Trico wiper vacuum motors in the January 2017 issue of Skinned Knuckles.
6
Things you are looking for. / Re: 29U hex style hubcap - wanted for reproduction
« Last post by 29UJohn on January 15, 2018, 02:42:36 AM »
Yes, I did receive two good ones.  I hope to have some Reproductions by this summer.  I need to take down this request.
Thanks.
John
7
Things you are looking for. / Re: 29U hex style hubcap - wanted for reproduction
« Last post by kimmc on January 15, 2018, 02:21:52 AM »
John:  Did you ever get a good cap?  If not, I will look through my collection; I may have one that might be acceptable to you.  Let me know at kimmc@softcom.net    Kim  Mc
8
General Discussion / Re: Radiator Emblem
« Last post by 29UJohn on January 13, 2018, 04:54:23 PM »
Chet, Thanks -  I'll have to save those instructions!
9
General Discussion / Re: Radiator Emblem
« Last post by chetbrz on January 11, 2018, 04:19:30 AM »
I posted a picture of a radiator emblem I rechromed using a hobby kit.  It is on the off-site photo page.  Unfortunately the emblem's curve di not match my radiator shell, it was too flat and looke bad on the shell, so I din't use it.

(I could not figure out how to take the picture so that the file size would be small enough to load here.)

John,

If you are using a windows based system right click on the Gallery image and go to properties and copy the image link.  Then click on the insert image icon (binoculars) in the forum "Post reply form" which is the first icon on the second line.  This action will insert the following code in your text {img][/img] Past your link in-between the image brackets.
{img]PAST LINK HERE[/img]   example:  {img]http://www.1948plymouth.info/galley/var/thumbs/29UJohn/Emblem.jpg[/img]



Larger image:



[img]http://www.1948plymouth.info/galley/var/resizes/29UJohn/Emblem.jpg{/img]
10
General Discussion / Re: Radiator Emblem
« Last post by 29UJohn on January 11, 2018, 03:12:18 AM »
I posted a picture of a radiator emblem I rechromed using a hobby kit.  It is on the off-site photo page.  Unfortunately the emblem's curve di not match my radiator shell, it was too flat and looke bad on the shell, so I din't use it.

(I could not figure out how to take the picture so that the file size would be small enough to load here.)
Pages: [1] 2 3 ... 10