• Welcome to 28Q29U Plymouth Forum.
 

News:

NEW FORUM version is here. 
If you are experiencing any problems, contact chetbrz@aol.com
WELCOME Auto Registration is turned OFF. 
In order to register for this forum please contact chetbrz@aol.com to request access.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - wellery

#61
General Discussion / Re: Need to Move Plymouth
October 11, 2011, 08:22:49 AM
Hoy Glenn

Didnt think it would be long before u hassled me about it  - got the door hanging from the garage so we can roll her in and bolt it straight up- we should be on the road with the girl later next week - All i need is Tinkeys address so we can drive passed and give him a look - I will have to get pics so I can post them here.  How are u doing ????

Hope all is well and God Bless

Wayne
#62
General Discussion / Re: Exhaust pipe size ?
October 08, 2011, 09:37:39 AM
Tony

What was the pricing like

Cheers

Wayne
#63
General Discussion / Re: front fenders
September 29, 2011, 01:38:58 AM
Gary

Your a gem that answers the question! - thanks mate

Wayne
#64
General Discussion / Re: Fabric/rubberized U-Joint Discs
September 27, 2011, 08:50:11 PM
Racer

Try the hard to source bits link on this forum - http://www.1948plymouth.info/28Q29U/index.php?topic=204.0

Or I make them out of old conveyer belt. found it to be the same material

Cheers

Wayne
#65
Well done Tony - you are a man of many talents!!!!!!!!!!!!!!!
#66
General Discussion / Re: front fenders
September 26, 2011, 10:07:21 PM
Gary

Have heard that the rear fenders on a 29U roadster are different than for the other models - is this true??

Cheers

Wayne
#67
Gary

What does the 1929 service bulletin list for the colours as I am yet to find out what olour mine was????


Cheers

Wayne
#68
Chet

did you see the door handle fall of when the bloke was doing some fitting of the rear door?

Cheers

Wayne
#69
General Discussion / Re: Need to Move Plymouth
September 19, 2011, 02:08:27 AM
Hi All

Glenn I new you would have a go at me - Tony is is about 3400 kilometres round trip - about the same as here to Perth - Chet thanks she will be a fun project as soon as I can get my hands on her. - A mate and I may meet half way and swap over the trailer.
#70
#71
General Discussion / Need to Move Plymouth
September 15, 2011, 10:17:03 PM
Hi all

Need to move 29u Plymouth Roadster from Brisbane Queensland to Geelong Victoria - what is the best way she will roll but not drivable  - container - car trailer - flat bed??

Priced one way car trailer cost around a grand to do it - plus fuel and 4 days on the road - might be cheaper options

any suggestions would be appreciated
#72
http://www.uniquecarsandparts.com.au/holden_production_1927_1930.htm

Check it out as it is interesting to see what bodies, and how may were made during the different periods - On top of article you can change the years of production by clicking the 'Select Period'

Anybody else have information on body building in Australia or the US?

Cheers

Wayne
#73
General Discussion / Re: Thinking of getting another car
September 06, 2011, 12:31:54 AM
go for it mate!!!!!!!!!!
#74
General Discussion / Re: 29 roadster doors
September 06, 2011, 12:30:48 AM
Glenn

Sent you a PM

Wayne
#75
There is a bloke in Geelong that I believe is a guru in shafts he has done a couple for me - even fixed up the farm ute when I launched on to some rocks - it was pretty bad

Your not slow just careful!!!!! lots of laughs