Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kimmc

Pages: [1] 2 3 ... 14
1
Things you are looking for. / bumper plates
« on: April 20, 2018, 03:24:42 AM »
I would like to buy 2 good "bumper plates" (picture attached).  The face on the ones I have is flat, not slightly curved like one I bought off the internet.  Thanks.  Kim Mc

2
General Discussion / Re: 1929 Weatherstrip - Questions
« on: April 16, 2018, 09:30:11 PM »
Hi Chet.  I have some pictures attached of my '29 coupe that may help you.  One picture shows the P-side door frame with windlass-type seal along the inside edge of the door opening.  This picture also shows the 4-piece garnish molding around the rear window.  Also note above the upper left corner of the rear window (L in picture) one of the two hangers for the roll-down type rear window shade.  I do not remember that there was any weatherstrip anywhere in the door jambs or door frame but I could be wrong about that.  The pictures don't show any evidence that a rubber seal was ever there however.  If I find a picture that clearly shows the hinge post and open door, I will send it along.  Kim

3
General Discussion / Re: plating on different parts...
« on: April 13, 2018, 05:53:12 PM »
Those parts on my car were once black as were the "retainer plates" on the front of the upper and lower chrome bars that hold those two bars in place.  Except for the chrome bars, I plan to have all of these parts powder coated black.  Has anyone else done this?

4
General Discussion / plating on different parts...
« on: April 12, 2018, 02:07:38 AM »
On the early Plymouths, like my '29, there seem to have been different plating coatings used on different parts.  I could use some help with this.

steel wheel rims:  cadmium   Did anything else receive cadmium plating?
bumpers:  chrome or nickel?  I've seen lots of chrome but an old timer told me they were nickel originally.  What is the consensus?
headlights and radiator cowl:  chrome?  My headlights are original (I believe) and chrome.  Same for radiator cowl?
door handles and window cranks:  nickel 

Did I leave anything out?  Thanks for the help.  Kim

5
General Discussion / Re: Master Cylinder Replacment Canister
« on: April 05, 2018, 01:56:58 AM »
Thank you Rich.  Just sent payment for 2 cans and lids per your instruction.  I appreciate your efforts.  Thanks again.  Kim Mc

6
Hi Chet.  I came across these diagrams of the wood floor detail in my car that I did years ago.  I thought I sent these to you.  In case I did not, I am resending them.  The topic of floor wood restoration or replacement seems to come up occasionally and I thought these might be of help to those working on restoration of old Plymouths.  I am getting back to work on my '29 after some years building 3 later model cars.  Still enjoy reading and using the Forum posts.  kim mc

7
General Discussion / Re: Master Cylinder Replacment Canister
« on: March 19, 2018, 09:01:01 PM »
Glad I saw this before the order date!  I will take 2 cans and caps.  Thanks so much.  Kim McCleneghan

8
General Discussion / Re: engine bay splash pans....
« on: January 16, 2018, 01:23:13 AM »
Hey Chet.  Thanks for taking the time to do this.  I think I can manage the fabrication from your very complete drawing.  Best, Kim Mc

9
General Discussion / Re: engine bay splash pans....
« on: December 06, 2017, 06:14:55 PM »
Not a problem Chet.  I am in no hurry.  I have projects that need doing in my shop to last a second life-time.  I need to find someone here that can do my engine.  The "big name" shop wanted $5K to start!!  Won't be going there.  Have a very good holiday season.  And thanks.  Kim Mc

10
General Discussion / Re: engine bay splash pans....
« on: December 06, 2017, 02:55:36 AM »
Yes, that would be great!  Flat pattern is fine (folded for mailing), maybe dotted lines to indicate location of bends.  Thanks a lot, Chet.  Kim Mc

11
General Discussion / Re: 29 Wire Harness
« on: November 29, 2017, 12:06:23 AM »
Good stuff to know.  Thanks Chet.   KMc

12
General Discussion / Re: 29 Wire Harness
« on: November 28, 2017, 02:15:50 AM »
what were the "extras" you got? 

13
General Discussion / Re: Happy Thanksgiving !!!
« on: November 23, 2017, 10:25:56 PM »
Happy Holidays to you and your family too Chet.  And thank you especially for managing and maintaining this site.  It is really great to be able to exchange information with other early Plymouth owners.  Best regards, Kim Mc

14
General Discussion / Re: engine bay splash pans....
« on: November 21, 2017, 08:32:08 AM »
Hey, thanks Chet for clearing that up.  Now I have to find the passenger side pan somewhere.  KMc

15
General Discussion / engine bay splash pans....
« on: November 21, 2017, 01:18:53 AM »
I have what I think is the passenger side "splash pan" that goes alongside the engine at the oil pan level in my '29 coupe (picture attached).  However, I just have the one and I have no idea what the piece on the other side looks like or even if there is one on the driver's side.  If one of you could send me a picture of the driver's side splash pan, I would appreciate it.  Then I can start looking for a replacement.  Thanks for the help.  Kim Mc

Pages: [1] 2 3 ... 14