Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - kimmc

Pages: 1 ... 8 9 [10] 11 12 13
136
General Discussion / Re: I need some advice...
« on: October 11, 2012, 08:52:43 AM »
Chet; it's not much extra work to get the pictures you want while I have it all open.  So just let me know; I'll be glad to get the detail pictures you want.

Al; I enjoy posting the pictures and getting feedback from forum members.  This is all part of the fun for me.  I've benefitted from the posts of others on this forum; I hope some will benefit from my adventures with the restoration of my car.

I am putting up a couple of more pictures of the top's wood structure.  You all are lucky that there is a 1000 KB size limit on posted pictures otherwise I'd be putting up lots more.  The first pic shows the top from above the left back corner of the cab (behind the driver) and the second show a broken support bow (there are 3 breaks like this...probably caused by high school friends piling all over the car on several occasions way back when I was just a lad).  I think these can be glued and clamped; I also plan to reinforce each top bow by gluing strips of wood along either side of each bow.  It can't hurt and will probably help the old wood a little.  And I have some other pieces that I will have to manufacture replacement pieces....but that's another post.  Thanks again for the feedback.  Kim

137
General Discussion / Re: New member - Plymouth 1929 Two Door Sedan
« on: October 11, 2012, 01:58:41 AM »
Hey Jonas.  Looks like a nice car.  The body looks good...I can't see any dents.  I am working on restoring my '29 Plymouth coupe.  I am posting my adventures on the forum; it started out under the title "I need some advice".  Lots of helpful folks on this forum.  You will always get a reply from someone who has encountered a similar problem.  Keep us posted on your progress.  Everyone likes to look at pictures!  Good luck.  Kim

138
General Discussion / Re: I need some advice...
« on: October 11, 2012, 01:28:46 AM »
Here's the 3rd photo.  All the floor boards laid out.  I will do a sketch of each with measurements if that will help.  Let me know what else you want.  Talk to you later.  Kim

139
General Discussion / Re: I need some advice...
« on: October 11, 2012, 01:25:34 AM »
Well, my frame is original...some dry rot but not too much.  I can send you all the pictures you want however mine is a coupe, not a sedan.  Yours is probably similar construction, just longer (and even more wood!).  I am sending 2 pics here taken just a couple of hours ago.  The 3rd pic will have to follow in a separate reply as the third picture would put me over the 1000KB limit.  Go to go.  My wife is making me take some time away from my project!

140
General Discussion / Re: I need some advice...
« on: October 10, 2012, 08:33:48 PM »
Hi Chet.  Sure I can do that.  Is there something that you are especially interested in?  There's a lot of wood and specially machined joints!  I want to be sure to get those parts that you want.  It may be a day or two as the floor of the old girl is pretty cluttered right now as I continue the disassembly.  I will post some pictures later today of the top wood structure; I removed the burlap this morning and took pictures.  I hope I can salvage most of the wood structure and only have to build a few pieces.  Later.  Kim

141
General Discussion / Re: I need some advice...
« on: October 10, 2012, 05:12:20 PM »
Thanks Glenn.  I appreciate the feedback and enjoy the humor.  The comments I get regarding my "posts" are part of the fun of this project and keep me plugging along.  Thanks for taking the time to post a note.  On my way out for another day.  They must have used at least a couple of boxes of tacks on that interior and top!  Kim

142
General Discussion / Re: I need some advice...
« on: October 10, 2012, 05:32:10 AM »
Well, for those of you checking on my progress I am continuing to disassemble the car.  The interior parts and upholstery are mostly out.  I spend a lot of time labeling and bagging parts and pieces.  Also I am taking lots of pictures and making sketches when I think a sketch will show something better than a photo.  I hope this will make things easier when the time comes to re-assemble the car.  Today I discovered some significant dry rot in the wood of the right rear corner beneath the fabric top.  Also, the wood piece across the top front of the cab may also need to be replaced but I don't have that completely exposed yet.  Looks like a shade-tree repair to the top was done "down on the farm".  Check out the picture of the burlap used beneath the top membrane.

143
General Discussion / Re: I need some advice...
« on: October 08, 2012, 06:31:09 AM »
Well, I spent some time the last couple of days continuing to remove parts, labeling and bagging lots of screws and bolts, and taking many pictures.  This afternoon I removed the old upholstered kick panels, door panels, garnish molding, and glass from the driver's side door.  All went pretty wells.  Some big old mouse nests behind the kick panels...pretty ugly.  I found a little dry rot on a floor board beside the bottom corner of the passenger door but after some poking with an ice pick, I don't think it is serious enough to require removal of the entire piece.  We'll see.  On the driver's side, a small wood piece inside the door that covers the rubber strap that limits the distance the door can open will have to be fabricated.  But it won't be a big job; I used to do quite a bit of wood working as a hobby.  I am posting a picture of the passenger door with its panels still intact (but worn), the driver's door with everything removed, and an upholster's tack removing tool that was invaluable to remove the many tacks without destroying the old fabric-covered panels.  I wanted to keep those in tact in order that I can eventually deliver them to an upholster so he can use them to see what was done on the original car.  Oh, and I found an old 1919 wheat sheave penny...maybe lost by my great grandfather?  I'll keep it to display with his picture when I finally take the car out for its first Plymouth Club meet.  Kim Mc

144
General Discussion / Re: Hubcaps - What do these fit?
« on: October 02, 2012, 11:44:08 PM »
OK....maybe there are wood and steel "artillery wheels".  I consulted another plymouth owner and here's what he sent me.  "The 1935 Ross Roy PJ Data book describes the wheel as “steel artillery”.  This is the book Plymouth furnished it’s dealers!"  So, it sounds to me like the early artillery wheels were wood with steel reinforcement and later the term was applied to the steel wheels like the ones pictured on my '35.  Hope that helps.  Kim

145
General Discussion / Re: Hubcaps - What do these fit?
« on: October 02, 2012, 08:59:22 AM »
SD Glenn;  I am attaching a picture of "artillery wheels" on my '35 Deluxe Sedan.  Regards, Kim Mc

146
General Discussion / Re: I need some advice...
« on: October 02, 2012, 03:01:11 AM »
Well, made a little progress today.  Things always take longer to do than I expect.  Removed everything from the firewall and from behind the dash today.  Next I plan to take lots of pictures of the old original interior.  It's pretty ratty (literally, in some places where they gnawed the seats) so I expect it will go but I'll record it and save the materials, at least for a while.  So, here's a pic of the firewall sans all the wires and cables that pass through it; I also included a diagram of the firewall wiring and cable layout for use later.  Kim

147
General Discussion / Re: I need some advice...
« on: October 01, 2012, 04:50:43 AM »
Chet; sure, that's fine with me.  Information sharing is what this site is all about, right?  Kim Mc

148
General Discussion / Re: OT - 2012 Leesburg VA Air and Car Show
« on: September 30, 2012, 11:52:47 PM »
Your car looks great.  Thanks, Chet.  Kim

149
General Discussion / Re: I need some advice...
« on: September 30, 2012, 05:42:10 AM »
I am attaching a sketch of how the front disk U-joint was assembled on my car.  I am nearly certain that these discs were original factory assembly.  The nuts of all 6 bolts were towards the rear of the car.  The "waffle" washers I think most will recognize.  There was also 1 combination washer on each bolt; it was waffled on one side and flat on the other.  The flat side was nearest the nut on the trans spyder and nearest the bolt head on the driveshaft spyder.  I presume this arrangement allows better distribution of the pressure against the disks when tightening the bolts.  I hope the diagram makes sense and it will be useful to some.  Happy wrenching...  Kim

150
General Discussion / Re: I need some advice...
« on: September 30, 2012, 02:21:11 AM »
Hi Frank.  Thanks for the correct terminology for the splash pan.  Mine needs a little re-shaping; that may be a good piece to start practicing "body work" on.  I need a little instruction first.  Yes, the gas tank was taken to a vendor that said they would take the dents out and coat it inside and out.  I was working out-of-state at the time.  I checked in a couple of times with them (they had my radiator, and radiator shell as well).  When I dropped in (two different times when I was home) they didn't know where my stuff was or if any work had been done.  This was supposedly a radiator shop that worked on vintage car stuff.  After 6 months I called them and said I was going to be in town and wanted to come by and talk to the owner; my stuff still wasn't done!  I went in and picked up all my parts after they searched for a while.  The fuel tank had been coated but no dents removed; they just coated right over them.  I was so @$#$% mad that I just took all my stuff and left.  I haven't decided what to do about the fuel tank; just leave it or have it redone (more $$$).  A lesson learned.  For my next post I am going to diagram the transmission-side fabric U-joint with bolts and washers as I found them.  I'm pretty sure these were original assembly.  I saw some discussion on the forum about the discs and "waffle" washers and I thought some of the forum members would be interested in how that was put together.  Anyhow, thanks for your responses.  I like talking with others that have plowed this same ground...the experience of "moss-backs" is very helpful.  Regards, Kim

Pages: 1 ... 8 9 [10] 11 12 13