• Welcome to 28Q29U Plymouth Forum.
 

News:

NEW FORUM version is here. 
If you are experiencing any problems, contact chetbrz@aol.com
WELCOME Auto Registration is turned OFF. 
In order to register for this forum please contact chetbrz@aol.com to request access.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - ski

#16
Not exactly sure what you're looking for but I'll post this anyway just in case. https://www.jalopyjournal.com/forum/threads/29-31-chevy-plymouth-dodge-windshield-crank-up-down.1254285/
#17
Outstanding Chet!
#18
General Discussion / Re: Wheel Maintenance
October 23, 2020, 07:02:47 PM
#19
General Discussion / Re: Wheel Maintenance
October 23, 2020, 06:56:45 PM
I've heard of that and it was specific whether it should be linseed oil or "boiled" linseed oil but can't remember which.
#20
General Discussion / Re: Street Legal
October 22, 2020, 01:28:07 AM
Way to go Chet! It's great to be legal.
#21
General Discussion / Re: 29 Build Thread - Part 3
October 18, 2020, 08:37:59 PM
Amazing job Chet. I learned a lot following along with your build. Here's to many happy miles ahead!
#22
She's a beauty John!
#23
General Discussion / Re: Rear Roof Trim
August 30, 2020, 11:03:23 AM
Chet, I'll be watching to see how you tackle this. It looks like some type of padding went over the wood slats and then the exterior roof fabric went over that and was pinched under the trim pieces and cut off even with the outer edge of the trim. I didn't have any of that left except some remnants of the outer fabric which is still under the trim.
ski
#24
General Discussion / Re: Rear Roof Trim
August 29, 2020, 07:56:28 PM
............few more
#25
General Discussion / Re: Rear Roof Trim
August 29, 2020, 07:55:28 PM
Here's how mine is Chet. The material is some type of nonmagnetic metal alloy. It's not soft like lead. It's held on by brass tacks through the sheet metal roof edge to the wood frame below. The roof edge is also screwed into the wood. On my coupe there are only three pieces total. The one big section is a single piece and then two short sections that terminate at the drip edge. It is is similar to the trim piece between the roof and quarter panel shown in the last two pics but these have tacks the seem to have been countersunk into the trim and filled with solder maybe. If you need any more info or pics just ask.
ski
#26
General Discussion / Re: Rear Roof Trim
August 28, 2020, 11:31:41 AM
You got it Chet. After I get some coffee in me I'll go out and snap some pics.
#27
General Discussion / Re: Rear Roof Trim
August 27, 2020, 11:30:43 PM
Chet, I have a 29U coupe. If pics of that would help I can take some. Mine has no insert but the trim appears all original. It may have different dimensions but the "treatment" may be the same.

ski
#28
General Discussion / Re: 29 Sedan
August 15, 2020, 11:19:15 AM
Yes Chet, its off to the left of center.  It's 18 1/4 from the center of the two riser screws to the edge of the mirror base on the drivers side and 18 3/4 between the same points on the other side.
ski
#29
General Discussion / Re: 29 Sedan
August 14, 2020, 11:12:10 PM
Hi Chet, If a 29 coupe is the same I could take a picture.
ski
#30
General Discussion / Re: 29 Build Thread - Part 3
June 26, 2020, 11:29:04 AM
Looks great. Real nice work Chet.