Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Articifer Tom

Pages: [1] 2 3 ... 7
1
General Discussion / Re: Generator/Charging Question
« on: September 09, 2018, 04:57:50 PM »
I keep mine adjusted to a little charging maybe 3 to 5 with driving lights on . Why risk boiling the battery . Also gage accuracy on 85 yo unit come in to play . I think 12 to 15 was out put of gens DR943's . My only draw back is with headlights on it go negative . But in my state can not drive after dark anyway .

2
Not sure what they look like on your cars can you post pic ?

3
Lock handles in twenties and thirties where on passenger side, was a safety regulation . Did not want some one opening a door  in to a horse or something . My door has separate level to lock it and is only on driver side ,so key must be on pass. side to lock it .

4
General Discussion / Re: Pressure Plate Refurb
« on: August 29, 2018, 03:33:22 AM »
I agree ,nice looking job . Other can always be sold .

5
General Discussion / Re: Member Sighting - Nowthen MN Show
« on: August 19, 2018, 07:08:40 PM »
Great !!! I'am sure people flocked to both to compare .

6
General Discussion / Re: 1930 30U Water Pump Oiler?
« on: August 14, 2018, 04:45:20 PM »
Retry,


7
General Discussion / Re: 1930 30U Water Pump Oiler?
« on: August 14, 2018, 04:31:33 PM »
Here some pics of friends . Is about 5/16" opening . Looks like grease in .

8
General Discussion / Re: Anyone want to venture a guess.
« on: August 08, 2018, 08:05:00 PM »
Sounds like you got it , Chet . It must have been the valve . That 7-8 is a hot setting , right . So maybe if was 11, back it to 10-9  cold . This is new stuff to me . So I am following close .

9
General Discussion / Re: Anyone want to venture a guess.
« on: August 07, 2018, 10:27:43 PM »
Is it the higher pitch clanking sound every rev or deep clunks , multiples per rev.  . Check fuel pump oil pump .

10
General Discussion / Re: 29 Build Thread - Part 2
« on: August 05, 2018, 02:40:08 AM »
Looking great Chet ! So the other plates were old style , which you using  ?   Also is carb on right direction , not familiar with the cars ? But love seeing it .

11
General Discussion / Re: 1930 30U Water Pump Oiler?
« on: August 04, 2018, 02:38:50 AM »
Not exactly like mine but similar . Would say marine grease in rear .

12
General Discussion / Re: Pressure Plate Located
« on: August 03, 2018, 10:54:58 PM »
Chet, when it rains it pours; found couple more in (parting out ) post .

13
General Discussion / Re: 1930 30U Water Pump Oiler?
« on: August 03, 2018, 10:52:18 PM »
There were couple different pumps in 30's do you have pic . Mine is oil front bushing and grease rear were holds water back and packing rope on shaft . Mine is on '31 Truck with PA engine . 

14
General Discussion / '28 Ply Sedan Parts For Sale
« on: August 03, 2018, 04:13:38 PM »
On aaca site in PARTS FOR SALE .  A stripped car with two engines parting out .

15
General Discussion / Re: Pressure Plate Located
« on: August 03, 2018, 03:41:17 PM »
Take number off bearing and cross on SKF site . Nice 1136 was mine . Ebayed about 34 dollars

Pages: [1] 2 3 ... 7