• Welcome to 28Q29U Plymouth Forum.
 

News:

NEW FORUM version is here. 
If you are experiencing any problems, contact chetbrz@aol.com
WELCOME Auto Registration is turned OFF. 
In order to register for this forum please contact chetbrz@aol.com to request access.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - frankp

#256
General Discussion / Re: Timing Gear
August 16, 2017, 05:25:53 PM
Try here.  If not listed, call and ask.

http://www.then-now-auto.com/
#257
General Discussion / Re: Could use some help
August 15, 2017, 08:19:25 PM
Chet,   the pictures are from Dave's car and measurements from mine. (platypus)
#258
General Discussion / Re: Could use some help
August 15, 2017, 05:24:34 PM
Chet disregard previous post - that is rear window!

Side window, I have 3".   I'd still poll John, Dave
#259
General Discussion / Re: Could use some help
August 15, 2017, 05:18:28 PM
Chet, mine looks to be from 3 1/2 to 3 5/8".  You may want to get a number from John &/or Dave for something original.
#260
General Discussion / Re: Could use some help
August 15, 2017, 04:47:27 PM
one more
#261
General Discussion / Re: Could use some help
August 15, 2017, 04:43:14 PM
Pictures of Dave's car.
#262
General Discussion / Re: Roadster Door Hinges
July 25, 2017, 11:50:57 AM
I have the same issue, but have not removed the door or kick panels to inspect.   29 and 30 appear to be the same.   frank
#263
General Discussion / Re: 29 Build Thread
July 09, 2017, 06:30:13 PM
Chet, Fantastic work!!
#264
Chet,

Was looking for info for Dave.  He is taking his out to replace glass and it doesn't go up/down properly.  I removed mine to put in safety glass a few years before the article and my memory is very sketchy.  I didn't remember removing the dash, but who knows.

frank
#265
Thanks, John.   Time flies, would not have guessed it was 15 years ago.  frank
#266
General Discussion / 29 Windshield Removal Article
June 05, 2017, 09:10:11 AM
Hi folks,

Anyone remember which Plymouth Bulletin had a good article on removing the windshield?

Thanks,
frank
#267
General Discussion / Re: Off on a Tangent
May 24, 2017, 07:33:48 PM
Nice Chet!  Just remember this is not a high falutin Chrysler!
#268
General Discussion / Re: Off on a Tangent
May 13, 2017, 12:16:52 PM
I believe kimmc used 2 part epoxy with sawdust as a filler.  Bondo in thin layers to fill holes and cracks?
#269
Chet-my sedan Kingston tank has no vacuum relief and works just fine.  I have seen it on Stewart tanks.

Rwollam-by looking at Chet's picture, the cork diameter is probably about 1.5" or so.  Interestingly my cork has not been replaced or coated since I've owned the car, 1965.  i 've been told corks can be coated with "DOPE" paint from a hobby store.  This was/is used on gas/alcohol engine model airplanes.
Your brass float may be in the wrong location on the shaft allowing the gas level to rise to high.  I had this problem when the top cork stay solder failed and the corks slid up the shaft.

good luck,
frank

(now I need a Kingston for the roadster)