Your new top looks great. Car look good also.
- Welcome to 28Q29U Plymouth Forum.
28Q29U Plymouth Forum
News:
NEW FORUM version is here.
If you are experiencing any problems, contact chetbrz@aol.com
WELCOME Auto Registration is turned OFF.
In order to register for this forum please contact chetbrz@aol.com to request access.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages1
#2
General Discussion / Re: Thanks for all the help
March 17, 2014, 09:45:25 PM
Here is a few pic;'s from the day I did the swap.
#3
General Discussion / Thanks for all the help
March 13, 2014, 07:57:10 PM
Hi Everyone
I wanted to let you all know that I have swapped my 30U for a 1954 Dodge pickup. It's been a lot of fun and educational being allowed to learn and make needed repairs to my Plymouth for the last few years. I have told the new owner about the forum. He will be checking it out soon. I'll still be checking in from time to time Thanks again for all the help.
I wanted to let you all know that I have swapped my 30U for a 1954 Dodge pickup. It's been a lot of fun and educational being allowed to learn and make needed repairs to my Plymouth for the last few years. I have told the new owner about the forum. He will be checking it out soon. I'll still be checking in from time to time Thanks again for all the help.
#4
General Discussion / Re: Question on front seats
September 29, 2013, 06:05:23 PM
Mine is also 3/4 inch. I believe that the second hole in my frame was put in by someone trying to get the seat a little closer to the peddles. This works for me as I'm not that tall.
#5
General Discussion / Re: Question on front seats
September 27, 2013, 05:49:04 PM
In my 30U Coupe There is a rail that runs along the bottom of the seat. On the front lip of the rail there are 2 small metal pegs tat the front board of the seat bottom rest on There are 2 holes on the board allowing the bottom of the seat to be adjusted about 2 inches closer to the steering wheel.
#6
General Discussion / Re: greetings
December 31, 2012, 08:21:08 PM
Happy New Year to all. Hope everyone had a very Merry Christmas.
#7
General Discussion / Re: I need some advice...
October 10, 2012, 08:16:01 PM
I just wanted to send a note to let you know how much I'm enjoying your post . Keep up the good work and thanks foe allowing us to watch as you proceed.
#8
General Discussion / Re: Motor Oil?
August 06, 2012, 07:04:55 PM
Just wanted to say thanks for the information.
#9
General Discussion / Motor Oil?
August 04, 2012, 04:11:09 PM
What type of oil do you use in the 30U?
#10
General Discussion / Re: MERRY CHRISTMAS and HAPPY NEW YEAR !!!!
December 23, 2011, 12:32:54 AM
Merry Christmas to every one. I hope you all have a happy and safe New Year.
#11
General Discussion / Re: Tools
July 17, 2011, 09:49:38 PM
I forgot to mention that the open end wrench has a #5 on it.
#12
General Discussion / Re: Tools
July 17, 2011, 09:45:43 PM
I have afew wrenches that cme with my 30U. Here is a pic of them.
#13
General Discussion / Re: Can't find engine number.
June 30, 2011, 09:50:25 PM
Here are a few pic's. Hope they help with motor ID.
#14
General Discussion / Can't find engine number.
June 28, 2011, 10:20:56 PM
I believe that I have a 1930U Plymouth. The body number is 383 373. The first thing I noticed that was odd is the trans is a 4 speed and the motor is different from any others I have seen in a 30U. I can't locate the engine number. I have found a casting number. It is 682529. There is water pump and manuel fuel pump on my motor. The distributor is on the right side to the rear of the oil filter. Any help in identifying the motor is welcome. I also want to thank all members for the posted information on rebuilding the brake system. I have put it to good use.
Pages1