Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Articifer Tom

Pages: [1] 2 3 ... 18
1
General Discussion / Happy Labor Day All !
« on: September 06, 2021, 07:58:17 PM »
Hope you got some drive time in this weekend . Did not on my end but will this week and next weekend .

2
Things you are looking for. / Re: front crank shaft pulley
« on: June 05, 2021, 02:55:05 PM »
He is looking for bottom /crank pulley .

3
General Discussion / Re: Unable to post pictures
« on: June 05, 2021, 02:53:52 PM »
Try size reduction .

4
General Discussion / Re: Running Board Question
« on: May 12, 2021, 06:23:27 PM »
Elevator bolt , Tee slot bolt or modified carriage bolt . 

5
General Discussion / Re: Just checking
« on: April 29, 2021, 09:25:49 PM »
Could not get at an edge of alum to mic . But ss is .030 to .034 or 21 gauge on corner of side where flat . I believe you have ss .

6
General Discussion / Re: Just checking
« on: April 28, 2021, 07:48:13 PM »
if you have both side by side it is easy to tell difference . The ss is thinner and harder . maybe a file to the edge . Your dark spots if alum. can be ware through of anodizing . I can mic both for you tomorrow unless you need tonight .
                            Tom

7
General Discussion / Re: Just checking
« on: April 28, 2021, 02:08:29 PM »
My Dodge used aluminum , but some Chrysler's used stainless . Accidental ebayed a pieced .

8
General Discussion / Re: CLUTCH AND PLATE INTERCHANGE FOR PLYMOUTHS #2
« on: April 06, 2021, 03:49:06 PM »
For clutches you can send out to a place that does fork trucks or hi lifts  and other like equipment .

9
General Discussion / Re: Clutch related question.
« on: February 18, 2021, 08:14:06 PM »
Pic from my BOI


10
General Discussion / Re: Throw out bearing
« on: February 18, 2021, 01:10:19 PM »
Any luck with bearing ?  There is good post on AACA Taylormade thread on Resurrection of Daphane . Pg 29 -31 .

11
General Discussion / Re: Clutch related question.
« on: February 18, 2021, 01:07:42 PM »
  Well lucky we have the clutch guru here CHET  ;D . He'll help with sizing . But your correct it is return spring from bearing holder to hole in inspection opening
    Mine is correctly attached to nut and bear guide rod . It is to troublesome to remove . I am not sure if correct either . But look like 12 to 13 coils . wire size and overall length will be needed from guru C . I donot think it is that critical as strength ,need only pull back reesure to keep bearing from riding and spinning againt clutch , thus slowing wear on . 

12
General Discussion / Re: Throw out bearing
« on: February 14, 2021, 09:08:09 PM »
From other ; crosses maybe Aetna A641-1   ,  BCA 1811   ,BJL  N847 .

13
General Discussion / Re: Exhaust pipe hangers
« on: February 09, 2021, 09:53:12 PM »
Good one Chet . That's what it looks like . Never knew about one off trans support . I'll check for evidence of on mine tomorrow .

14
General Discussion / Re: Exhaust pipe hangers
« on: February 09, 2021, 09:35:21 PM »
oops backwards  ..Poor front pic .

15
General Discussion / Re: Exhaust pipe hangers
« on: February 09, 2021, 09:33:44 PM »
here is pic of rear . Front is same only sideways off frame rail . Do not have pic but can take one tomorrow .
 

Pages: [1] 2 3 ... 18