• Welcome to 28Q29U Plymouth Forum.
 

News:

NEW FORUM version is here. 
If you are experiencing any problems, contact chetbrz@aol.com
WELCOME Auto Registration is turned OFF. 
In order to register for this forum please contact chetbrz@aol.com to request access.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - Articifer Tom

#301
General Discussion / Re: Radiator Emblem
December 20, 2017, 08:29:55 AM
Does have the duller look of nickel . Nickel is easily electrically applied or plated . I use to do on belt buckles instead of silver that dulls out faster . Redid my gage bezel came out decent .
#302
General Discussion / Re: 29 Build Thread - Part 2
December 14, 2017, 06:09:08 PM
No middle of eastern Pa. Hour and half north of Hershey .  You probably went up I 95 thur Jersey .
#303
General Discussion / Re: 29 Build Thread - Part 2
December 14, 2017, 03:53:37 PM
Yeah !  Chet hope you did not go up I81 with out stopping to say hello . Live at Jct of I81 x I80 .
Checked JM site man engine is dirty and water plugs where about to go on you . .
#304
General Discussion / Re: engine bay splash pans....
December 07, 2017, 08:36:18 PM
I see . Mine being later engine and horn  is off second stud from back on top .
#305
General Discussion / Re: engine bay splash pans....
December 06, 2017, 07:39:46 PM
Yeah . no problem here either . Make sure your rebuilder puts the longer head stud in right spot , for horn mounting .
#306
General Discussion / Re: engine bay splash pans....
December 05, 2017, 04:05:27 PM
That would be great .  Bend paper to piece ,  trace on  and send me a copy . Gladly reimburse  you .
#307
General Discussion / Re: 29 Build Thread - Part 2
December 04, 2017, 08:34:59 PM
Hello Chet ,  So your engine is not original paint ,your saying . I do not know about orange manifold ,where did you see  that?  Also see what Dupli. Color or Rusto. Color matches  . The salesman book on my truck with Ply. 4 says head is Gray, not Silver with block  black . Was thinking of using a aluminum color hi-temp . But discussion on aaca seems to think water cooling engine surface temp will only be about or below 210*F ,boiling point  most paints can easily with standing , excluding manifold .
#308
General Discussion / Re: Happy Thanksgiving !!!
November 23, 2017, 02:58:31 PM
Happy Thanksgiving All !
#309
General Discussion / Re: engine bay splash pans....
November 21, 2017, 10:40:14 PM
Thanks Chet . Looks like my pan is same . It does not have extra hole where exhaust goes threw . That pic of tie piece is enough for me to fab a piece between . Did not know about it going under motor mount .
#310
General Discussion / Re: Leaking Wheel Cylinder Question
November 21, 2017, 09:37:08 AM
The boots only keep dust and dirt out to minimize wear .The cup inside holds fluid back . You may have a corroded piston . These are aluminum and sometimes the cups do not seal around good enough if bad . I would send back , piston are not ready available , although heard maybe cross to some Chevy 1-1/4" stuff .
#311
General Discussion / Re: engine bay splash pans....
November 20, 2017, 09:42:38 PM
Do you have pic  of front tie between piece . That is one I am missing . My driver side is a different I think too . Will check . Same engine but on 31 Graham truck , whom I believed used Plymouth or Desoto frames .
#312
General Discussion / Re: WME Shackle
November 13, 2017, 08:10:38 AM
  Looks like a match to my truck . Still curious who made . I assume yours fit .
#313
General Discussion / Re: WME Shackle
November 06, 2017, 10:12:47 PM
I still have the one 3" from Jay  $25 plus shipping . Let me know if you want pic of wear in caps .
#314
General Discussion / Re: WTF Carter 209s breakdown
October 21, 2017, 08:49:01 AM
Got one ! If anyone needs let me know .
#315
Things you are looking for. / WTB Tyron front Shackles
October 15, 2017, 09:12:25 AM
Looking for front shackle 2-1/4" outter hole  . need One . Used on Plymouths and Dodge Trucks 28- 32
                  Thanks Tom