Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 1929luv

Pages: [1] 2 3 ... 7
1
General Discussion / Re: Door Stop Straps
« on: July 14, 2014, 10:34:51 PM »
they are expensive but Steele Rubber has the right ones for sale I used them on my project.  Good luck Craig

2
General Discussion / Re: Fuel delivery problem?
« on: March 12, 2013, 09:50:06 PM »
fuel regulator is your problem I have had this problem to the diaphragm goes bad and causes restriction.  Good luck If mine I would put original pump on it Craig

3
General Discussion / Re: Fuel line size
« on: January 08, 2013, 10:25:57 PM »
the steel line in picture should be a rubber flex line.  But looks great.  All the vaccuum tank I have seen have been natuaral looking, I powerder coated mine silver to look naturaul. Good luck Craig

4
General Discussion / Re: greetings
« on: December 29, 2012, 10:34:39 AM »
Hope all had a very MERRY CHRISTMAS and will have a HAPPY NEW YEAR!!! May we remember the reson for the season and be thankful.  MAy God bless US Craig

5
General Discussion / Re: Fuel line size
« on: December 29, 2012, 10:31:51 AM »
it is 1/4" copper from tank to vaccum pump and I had to make my ruber flex line and made it 1/4" too.  Good luck my fitting were original and would not fit new ones Happy motoring Craig

6
General Discussion / Re: Happy Thanksgiving !!!
« on: November 22, 2012, 09:41:09 PM »
Thanks Chet and plymouth friends


Hope all is safe n having a Happy Thanksgiving Happy motoring Craig

7
General Discussion / Re: Repairing pot metal
« on: November 15, 2012, 09:26:50 PM »
The only way that pot metal can be fixed is to plate it with copper, then solder it together then re copper it, fine sand it, then plate it.  These are the basic steps of repairing pot metal.  It is a very timely process an requires a plater to do copper process.  rem this is the bacis process and I would cast door handles before repairing old ones much cheaper in long run.  Only rare pot metal should be repaired for cost reasons. Good luck Craig

8
General Discussion / Re: Help needed
« on: October 23, 2012, 09:57:23 PM »
My dist. was sloopy and making noise and jumping on accation.  It was noisy.  Good luck Craig

9
General Discussion / Re: Front License Plate Mounting '28-30
« on: August 09, 2012, 11:44:15 PM »
the last picture of them hanging on the front of head lamp bar is the same as my '29.  Easy to make mine has a screw in middle to tighten arounf bar and a dimple on the license plate end to retain the plate.  Good luck Craig

10
General Discussion / Re: Visitor from Down Under
« on: June 19, 2012, 08:30:03 PM »
here is the e-bay number for the gasket set they have gone up to 215 and change.  ebay Item number: 170851845438
  good luck Craig

11
General Discussion / Re: Rear shackles and steering box lubricant
« on: June 13, 2012, 10:03:39 PM »
rare parts made all of my stuff for shackles and they have all the specs and sell them now aftedr I gave them all the spec and let them make them from mine.  Rare Parts 800 621 2005 and ask for Ted

12
General Discussion / Re: Visitor from Down Under
« on: June 13, 2012, 10:01:12 PM »
I got mine off of ebay $189.00 us dollars and it was a great set.  They are one there all the time Good luck Craig  What small stuff you  looking for. Im in austin TX area

13
General Discussion / Re: Throttle and Light switch levers
« on: June 13, 2012, 09:56:45 PM »
the Spark controls are just cast handles that have been chromed as of now like picture shows.  They are bonded to the steel handle rods and that can be done with a 3M product called panel bond or I can put them on a set of lever rods I have now.  I only have one set handles left that has been cast and chromed.  I can cast more if needed.  Here are the picks of before and after of the levers.  Let me know Craig

14
General Discussion / Re: Throttle and Light switch levers
« on: May 31, 2012, 09:32:00 PM »
I have found the spark control levers let me know thanks Craig

15
General Discussion / Stuff for sale removed
« on: May 29, 2012, 10:44:57 PM »
I had the spark levers listed on stuff for sale and it has been removed anlong with a lot of other good info.  Thanks Craig

Pages: [1] 2 3 ... 7