Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Articifer Tom

Pages: [1] 2
1
General Discussion / Steering box disassembly
« on: September 21, 2020, 08:41:10 PM »
Anyone here ever that there steering box apart . Am I correct in the worm is not removable from column . Maybe someone has pic of parts laid out . Trying to find easiest way to ship . Maybe disassembling gear worm pitman shaft half ? 

2
Things you are looking for. / Steering box info / Radiator tank
« on: September 06, 2020, 01:23:24 PM »
Working on my steering box on my '31 truck UF10 . Warner Sector worm .  Worm number 42834 , tooth gear 309449 . If any body has Plymouth master book could see if any car crossed . i've found that Dodge DD6 do .  Also want to check Chrysler .
    Also looking for bottom of radiator to try an salvage a original honey-cone radiator . Bottom outlet rust out and damage tank .

3
General Discussion / steering box adjustments
« on: September 06, 2020, 01:15:58 PM »
Anybody do it on vehicle . I tried ,but con not feel first adjustment the column . Do I have to loosen all other adjustment before starting ???    The BOI only says about loosening dash brackets and clamp bolt . And jacking up front end .
   i also have request in" looking for " forum .

4
General Discussion / What was used between Running Board Trim ?
« on: May 19, 2020, 07:44:34 PM »
     Hello all . Got some remnants of running board trim that where broke and missing parts ,to put back on my '31 . I've repaired the splits an added pieces on edges of the aluminum rb trim . Had to totally make new short ends and 6" of back angle . Used round wood form to reshape front trim . I noticed pieces of webbing riveted to end pieces .  What should be between end and back to steel ? Was it web even to top or a beaded trim ?

5
General Discussion / Drt-08 209 fixing
« on: April 18, 2020, 08:43:20 PM »
Hello All .  I been working on my 209 carb to get it working . Had it rebuild and was done with incorrect RJH parts . Been working on a year , on and off along with some others with same rebuild on AACA site . I determined idle tube need to have lower jet hole increased and inside jet restriction reduced . Just doing that got it starting and running . Did not road test was Winter , at time .  Disassembled again since repaired exhaust and manifold leaks. Want to check out specs of orifices in replaced standpipe and cone . From some holes in top of pipe missing and parts near bottom not reinstalled . Are ther not need now ??? Attached is pic of pieces and spring with questions I have . Any help would be appreciated .
  I think Frank29u did some work on his years ago , any input please .

6
Stuff 4 Sale / Es-50 Tie rod for sale
« on: April 14, 2020, 04:38:06 PM »
On ebay Thompson products ES-50 .It is what is on mine . maybe other here . I know Desoto's . They are right and left hand threaded . With leather washer on top .

7
General Discussion / Fans Self Destructing
« on: June 01, 2019, 08:05:21 PM »
Any of you been following the AACA thread on Mopar 20's and 30's fan developing cracks because of lap design and age w/  flexing ?
   Some have exploded taking out radiators and punching through the hood doors . Many are replacing with modern six blade racing fans trimmed and balanced . 
https://forums.aaca.org/topic/326980-1929-dodge-da-phaeton-fan-disaster/

8
General Discussion / Fuel Line ? Steel or Copper
« on: March 31, 2019, 03:54:24 PM »
 My steel fuel line needs replacing , not sure if it is original . Changes  to copper going thur frame in front before going up onto fuel pump .  Thought anyone , It is my '31Dodge  with PA 4 cyl engine .

9
Things you are looking for. / measurements tail pipe clamp
« on: March 25, 2019, 07:02:12 PM »
Pic of Dodge and maybe other Mopars tail pipe extension and clamp . Would like stock sizes and measurement to repo for mine , truck . Also pipe OD . Thanks in advance .

10
Stuff 4 Sale / Detroit Joint rebuild kit
« on: November 24, 2018, 02:48:07 PM »
On ebay now rebuild kit for 30-31 front or rear joints . Not mine , 155+ .

11
General Discussion / '28 Ply Sedan Parts For Sale
« on: August 03, 2018, 10:13:38 AM »
On aaca site in PARTS FOR SALE .  A stripped car with two engines parting out .

12
General Discussion / Minor problem help
« on: July 29, 2018, 09:52:52 PM »
Recently got my tilt windshield working . Will not stay open driving . Has flat waster under wingnut . Is something else needed ie. rubber washer toothed washer ?
                      Thks Tom

13
General Discussion / Info needed on brake line
« on: July 06, 2018, 11:47:52 PM »
Looking for info to make a brake reservoir to master tube . Mine was PO changed to braided hose . First is it 1/4 or 5/16 od copper and total length . And if you know nut size and thread . Thanks .   

14
Things you are looking for. / WTB Tyron front Shackles
« on: October 15, 2017, 09:12:25 AM »
Looking for front shackle 2-1/4" outter hole  . need One . Used on Plymouths and Dodge Trucks 28- 32
                  Thanks Tom

15
General Discussion / WTF Carter 209s breakdown
« on: October 09, 2017, 10:26:08 PM »
Hello , looking for parts list on a Carter 209s for Pa engine . I want to rebuild a unit I picked up . Also help on making a replacement or changing choke tube that's broke . I believe some have build copper replacements .
            thank you Tom

Pages: [1] 2