Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Articifer Tom

Pages: [1] 2 3 4
1
General Discussion / Re: Exhaust system question
« on: Today at 12:55:42 AM »
Yes , same number for Merch Exp , UF-10 ,F-10 attached with 5/16 x24 x 3/4" hex head bolt number 120741 cadium finish .

2
General Discussion / Re: Exhaust system question
« on: February 21, 2018, 01:34:58 AM »
Do not really know . Do not have tail pipe on mine yet . There are two styles on the trucks . A long sloping to up over the axle and like your lube chart and the four cylinder trucks a hump right at axle . Neither should change this detail . I have ask friend for close up of bracket . May take till he can get to .


3
General Discussion / Re: Exhaust system question
« on: February 20, 2018, 11:54:45 PM »
Here Chet . This is a friends UF10 like mine which has same frame layout . He had new exhaust ,but looks like old hangers .


4
General Discussion / Re: Exhaust system question
« on: February 20, 2018, 03:58:07 AM »
You can see hanger on the above drawing . It is on tank cross frame and the down curve of pipe . Seen in other pics some where on AACA site .

5
General Discussion / Re: Foot rest bent - Any ideas on how to repair?
« on: February 03, 2018, 06:33:26 PM »
Yes on tubing sizes . Electrical will not work all are inside measured and none exactly . Tractor Supply may have , done know about length . Any fab shop should have .

6
General Discussion / Re: engine bay splash pans....
« on: January 20, 2018, 03:18:39 AM »
Received mine in mail today . Thanks again . will post finish product , maybe awhile been busy baby sitting for 3 more weeks as daughter recovers from second grand daughters birth . also weather been terrible for me .

7
Things you are looking for. / Re: Water Outlet Elbow '29
« on: January 10, 2018, 12:31:17 AM »
Common problem . If you do not need original . Mine had straight on it with a flex hose to radiator and a second hose inside to fill out to size of 2 1-8" rad . Take to your local shop with stat and match flange and holes .
  Good Luck  Tom

8
General Discussion / Re: Merry Christmas / Happy Holidays
« on: December 24, 2017, 04:58:10 PM »
Ditto from  Tom

9
General Discussion / Re: Radiator Emblem
« on: December 20, 2017, 03:29:55 PM »
Does have the duller look of nickel . Nickel is easily electrically applied or plated . I use to do on belt buckles instead of silver that dulls out faster . Redid my gage bezel came out decent .

10
General Discussion / Re: 29 Build Thread - Part 2
« on: December 15, 2017, 01:09:08 AM »
No middle of eastern Pa. Hour and half north of Hershey .  You probably went up I 95 thur Jersey .

11
General Discussion / Re: 29 Build Thread - Part 2
« on: December 14, 2017, 10:53:37 PM »
Yeah !  Chet hope you did not go up I81 with out stopping to say hello . Live at Jct of I81 x I80 .
 Checked JM site man engine is dirty and water plugs where about to go on you . .

12
General Discussion / Re: engine bay splash pans....
« on: December 08, 2017, 03:36:18 AM »
I see . Mine being later engine and horn  is off second stud from back on top .

13
General Discussion / Re: engine bay splash pans....
« on: December 07, 2017, 02:39:46 AM »
Yeah . no problem here either . Make sure your rebuilder puts the longer head stud in right spot , for horn mounting .

14
General Discussion / Re: engine bay splash pans....
« on: December 05, 2017, 11:05:27 PM »
That would be great .  Bend paper to piece ,  trace on  and send me a copy . Gladly reimburse  you .

15
General Discussion / Re: 29 Build Thread - Part 2
« on: December 05, 2017, 03:34:59 AM »
Hello Chet ,  So your engine is not original paint ,your saying . I do not know about orange manifold ,where did you see  that?  Also see what Dupli. Color or Rusto. Color matches  . The salesman book on my truck with Ply. 4 says head is Gray, not Silver with block  black . Was thinking of using a aluminum color hi-temp . But discussion on aaca seems to think water cooling engine surface temp will only be about or below 210*F ,boiling point  most paints can easily with standing , excluding manifold .

Pages: [1] 2 3 4