Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Articifer Tom

Pages: [1] 2 3 4
1
General Discussion / Re: 29 Build Thread - Part 2
« on: December 15, 2017, 01:09:08 AM »
No middle of eastern Pa. Hour and half north of Hershey .  You probably went up I 95 thur Jersey .

2
General Discussion / Re: 29 Build Thread - Part 2
« on: December 14, 2017, 10:53:37 PM »
Yeah !  Chet hope you did not go up I81 with out stopping to say hello . Live at Jct of I81 x I80 .
 Checked JM site man engine is dirty and water plugs where about to go on you . .

3
General Discussion / Re: engine bay splash pans....
« on: December 08, 2017, 03:36:18 AM »
I see . Mine being later engine and horn  is off second stud from back on top .

4
General Discussion / Re: engine bay splash pans....
« on: December 07, 2017, 02:39:46 AM »
Yeah . no problem here either . Make sure your rebuilder puts the longer head stud in right spot , for horn mounting .

5
General Discussion / Re: engine bay splash pans....
« on: December 05, 2017, 11:05:27 PM »
That would be great .  Bend paper to piece ,  trace on  and send me a copy . Gladly reimburse  you .

6
General Discussion / Re: 29 Build Thread - Part 2
« on: December 05, 2017, 03:34:59 AM »
Hello Chet ,  So your engine is not original paint ,your saying . I do not know about orange manifold ,where did you see  that?  Also see what Dupli. Color or Rusto. Color matches  . The salesman book on my truck with Ply. 4 says head is Gray, not Silver with block  black . Was thinking of using a aluminum color hi-temp . But discussion on aaca seems to think water cooling engine surface temp will only be about or below 210*F ,boiling point  most paints can easily with standing , excluding manifold .

7
General Discussion / Re: Happy Thanksgiving !!!
« on: November 23, 2017, 09:58:31 PM »
Happy Thanksgiving All !

8
General Discussion / Re: engine bay splash pans....
« on: November 22, 2017, 05:40:14 AM »
Thanks Chet . Looks like my pan is same . It does not have extra hole where exhaust goes threw . That pic of tie piece is enough for me to fab a piece between . Did not know about it going under motor mount .

9
General Discussion / Re: Leaking Wheel Cylinder Question
« on: November 21, 2017, 04:37:08 PM »
The boots only keep dust and dirt out to minimize wear .The cup inside holds fluid back . You may have a corroded piston . These are aluminum and sometimes the cups do not seal around good enough if bad . I would send back , piston are not ready available , although heard maybe cross to some Chevy 1-1/4" stuff .

10
General Discussion / Re: engine bay splash pans....
« on: November 21, 2017, 04:42:38 AM »
Do you have pic  of front tie between piece . That is one I am missing . My driver side is a different I think too . Will check . Same engine but on 31 Graham truck , whom I believed used Plymouth or Desoto frames .

11
General Discussion / Re: WME Shackle
« on: November 13, 2017, 03:10:38 PM »
  Looks like a match to my truck . Still curious who made . I assume yours fit .

12
General Discussion / Re: WME Shackle
« on: November 07, 2017, 05:12:47 AM »
I still have the one 3" from Jay  $25 plus shipping . Let me know if you want pic of wear in caps .

13
General Discussion / Re: WTF Carter 209s breakdown
« on: October 21, 2017, 02:49:01 PM »
Got one ! If anyone needs let me know .

14
Things you are looking for. / WTB Tyron front Shackles
« on: October 15, 2017, 03:12:25 PM »
Looking for front shackle 2-1/4" outter hole  . need One . Used on Plymouths and Dodge Trucks 28- 32
                  Thanks Tom

15
General Discussion / Re: WME Shackle
« on: October 15, 2017, 04:16:31 AM »
I have two of those a front and rear , that Jay gave me to try on my pickup in place of Tryon . If you need any ,suspect he pulled from a Chrysler . I want to stay with Tyron went I find .

Pages: [1] 2 3 4